- Pump filter for AXYZ CNC Router only. 

OVERVIEW: 
 The optional Automated Label Printer is a fast and accurate method of panel identification for PANELBuilder machines. The device prints using thermal printing technology, requiring both thermal transfer ribbon and label rolls. The label applicator houses the suction pad which is used to pick up a label from the printer using vacuum pressure. The machine is programmed to apply the label onto a specified location on the workpiece.
 
Couple the Automated Label Printer with PANELBuilder software version 19 or higher to use the state-of-the-art PANELTracker feature. PANELTracker allows you to manage the workflow of your production process. Minimize rework and wait time with this great new tracking feature!

BENEFITS: 
·         The Automated Label Printer prints and applies labels onto panels using bar code technology. Automatic label printing speeds up the labeling process and reduces the number of costly mistakes.
·         The Automated Label Printer is fully compatible with the PANELTracker software, which enables easier tracking of damaged panels.
The Automated Label Printer comes with standard or user-definable label locations, templates and defined label generation

- Origin: UK

- The 12VDC Solenoid - 3 Port valve is the most commonly installed solenoid valve on a machine.
They are used for ATC spindles, vacuum control zones, pop up pins, and other pneumatic devices.
- For AXYZ CNC Router only

This sensor directly connects to sensor cabling.
- For AXYZ CNC router only

The Creasing Wheel is for polypropylene. The diameter of the wheel is 24 mm and has a thin cutting edge. This product comes with the axil included as shown in the images.
- For AXYZ CNC router only

The knife calibrator is a laser-based, non-contact sensor used for alignment correction and tool length detection of knife blades. The sensor is installed on the machine’s tabletop and is fitted with a sensor cover to protect the emitter and receiver from debris. The sensor operates in a similar fashion to the photoelectric beam seen in most garage door systems.

The sensor determines the angle and length of knife blade tools, eliminating the need for operators to manually set knife tools. The device is compatible with a variety of
standard oscillating knife blades and tangential saber blades.
• The sensor accurately and safely measures knife blades
• Reduces quality issues such as cutting too deep or “rough” edges on parts caused my manual alignment
• Saves time during setup
• Prolongs the life of the cutting mat
• Improves safety to operators by minimizing blade handling
• Increases life of blades by calibrating the knife angle accurately as opposed to manually
Technical Specification:
Accuracy of Knife Alignment = +/- 0.5 Degree
Accuracy of Tool Tip for Oscillating Knife = +/- 0.008''
Machine Compatibility:
The Knife Calibration device is compatible with all Trident, AXYZ Series and Infinite machines.
OS Compatibility (min.): 6.6A RC1
A2MC Controller (min.): A2MC Revision 6
For AXYZ CNC router only
496. High Pressure Tube Coil (80/60 & 80X only)
497. Creasing Wheel B32 - Polypropyle 24mm
The Creasing Wheel is for polypropylene. The diameter of the wheel is 24 mm and has a thin cutting edge. This product comes with the axil included as shown in the images.
- For AXYZ CNC router only

Phenolic Pressure Foot Donut is top-down mounted for mounting on Infinite Cast Pressure Feet. For Integrated Wand System.

For AXYZ CNC router only

- To engrave / craving on brass material

- For added safety, we have produced a SmartConsole with an E-Stop button mounted on the device, this allows the operator to stop the machine in case of an emergency. 

- For AXYZ CNC Router only

This component is the entire Smartconsole and will operate with any version of A2MC controller. Smartconsoles are very rugged and designed for industrial use but can be damaged by dropping or other very high impact events.
- For AXYZ CNC Router

This component is the entire Smartconsole and will operate with any version of A2MC controller. Smartconsoles are very rugged and designed for industrial use but can be damaged by dropping or other very high impact events.
Note: This SmartConsole is a direct replacement for SmartConsoles with a 4 pin cable connection.
- For AXYZ CNC Router only

- This is a direct replacement cable that can be used on both the subconsole and 4-pin SmartConsole.
Console cables are damaged by excessive stretching by cutting or impact. Generally, failed subconsoles or 4-Pin SmartConsoles can be repaired by simply replacing the cable.
- For AXYZ CNC Router only

- The Smartconsole Faceplate can easily be replaced if it is worn out or damaged. This is a membrane switch faceplate, so a new one is required if keys are sticking or broken.
- For ''AXYZ'' CNC Router only

- Phenolic Pressure Foot Donut is top-down mounted for mounting on Infinite Cast Pressure Feet.
- For Integrated Wand System.
- For AXYZ CNC Router only

The Universal 5Y pressure foot plays just as vital a role as the high capacity pressure foot. It has been specifically engineered to accept 2'' or 4'' diameter hoses and allows for manual adjustment of the ride height for faster material and tool setup often demanded in today's busy workplace.
This is ideal for use in situations where the material being processed may be damaged by a conventional pressure foot.
The Universal 5Y Pressure Foot can be easily set to ride just a short height above the material surface. Swarf extraction is highly efficient thanks to the unique internal cyclonic design.

• Single head machines require the left hand option
• Dual head machines require the right hand option
• The 5Y pressure foot can be used with both 2'' and 4'' diameter hoses.
• Longer stroke versions are available for machines with higher Z allowances. Please contact us for further information and manufacturing lead times for longer stroke versions of the 5Y pressure foot.

- Phenolic Pressure Foot Donut is top-down mounted for mounting on Infinite Cast Pressure Feet.
- For Integrated Wand System.
- For AXYZ CNC Router only

- 5Y Pressure Foot - Intergrated Wand System.
- Dual Head Machines require the right hand option.
- Compatible with Infinite Machines.
- For AXYZ CNC Router only

- 5Y Pressure Foot - Intergrated Wand System.
- Single Head Machines require the left hand option.
- Compatible with Infinite Machines
- For AXYZ CNC router only

- For AXYZ CNC Router only

- For AXYZ CNC Router only

- For AXYZ CNC Router 

- High performance, low-cost solution suitable for use on a variety of CNC applications. The power behind the AVS lies in its software which is fully integrated with the A2MC Control system. The digital print finishing benefits from the ability to quickly find and recognize conventional registration marks and adjust the machine cutting path as necessary to achieve exact alignment with printed shapes. The AVS is compatible with all cutting tools and allows virtually any printed material to be cut including card, vinyl, rubber, foam, aluminum, wood, acrylic and many more.

- The cable fits a either the 3HP or 5hp ELTE spindles. 
- For AXYZ CNC Router 

- For AXYZ CNC Router