- Pump filter for AXYZ CNC Router only. 

- The 12VDC Solenoid - 3 Port valve is the most commonly installed solenoid valve on a machine.
They are used for ATC spindles, vacuum control zones, pop up pins, and other pneumatic devices.
- For AXYZ CNC Router only

This sensor directly connects to sensor cabling.
- For AXYZ CNC router only

- To engrave / craving on brass material

For added safety, we have produced a SmartConsole with an E-Stop button mounted on the device, this allows the operator to stop the machine in case of an emergency.

- For AXYZ CNC Router only

This component is the entire Smartconsole and will operate with any version of A2MC controller. Smartconsoles are very rugged and designed for industrial use but can be damaged by dropping or other very high impact events.
- For AXYZ CNC Router

- Phenolic Pressure Foot Donut is top-down mounted for mounting on Infinite Cast Pressure Feet.
- For Integrated Wand System.
- For AXYZ CNC Router only

- Phenolic Pressure Foot Donut is top-down mounted for mounting on Infinite Cast Pressure Feet.
- For Integrated Wand System.
- For AXYZ CNC Router only

- 5Y Pressure Foot - Intergrated Wand System.
- Dual Head Machines require the right hand option.
- Compatible with Infinite Machines.
- For AXYZ CNC Router only

- 5Y Pressure Foot - Intergrated Wand System.
- Single Head Machines require the left hand option.
- Compatible with Infinite Machines
- For AXYZ CNC router only

- For AXYZ CNC Router only

- For AXYZ CNC Router only

- The cable fits a either the 3HP or 5hp ELTE spindles. 
- For AXYZ CNC Router 

- For AXYZ CNC Router

Pressure mat safety systems are installed onto the floor around your AXYZ CNC Router. These are used to guard the operator/persons by stopping anyone entering the cutting zone. The pressure mat operates when pressure is applied to the mat surface. This result is the machine will stop (pause) until the zone is clear and the job will need to be re-started by the operator. The machine cannot be run while pressure is applied to the mat surface.
The pressure mat safety system can be installed around one side, two sides, three sides or all four sides of your AXYZ CNC Router.

Note: A2MC R.7 Control System and SmartConsole required

- Oil dripper to be used in conjunction with the oscillating knife option to ensure proper maintenance procedures are followed.

- The Unist Air Metering Screw is a replacement part for a Unist misting system.

The Universal 5Y pressure foot plays just as vital a role as the high capacity pressure foot. It has been specifically engineered to accept 2'' or 4'' diameter hoses and allows for manual adjustment of the ride height for faster material and tool setup often demanded in today's busy workplace.
This is ideal for use in situations where the material being processed may be damaged by a conventional pressure foot.
The Universal 5Y Pressure Foot can be easily set to ride just a short height above the material surface. Swarf extraction is highly efficient thanks to the unique internal cyclonic design.

• Single head machines require the left hand option
• Dual head machines require the right hand option
• The 5Y pressure foot can be used with both 2'' and 4'' diameter hoses.
• Longer stroke versions are available for machines with higher Z allowances. Please contact us for further information and manufacturing lead times for longer stroke versions of the 5Y pressure foot.

The bellows system provides an extremely efficient vacuum performance. The bellows completely enclose the tooling, virtually eliminating all vacuum leakage.
This assembled pressure foot bellow is to be used in conjunction with the old style pressure foot
Compatible with all 5Y Pressure Feet.

- The Universal Lexan Seal is used to optimize vacuum performance on systems that are not using nose riders or bellows.

- For AXYZ CNC Router only

- The universal adjustable nose riding system is designed to fit with high capacity pressure and is used to very precisely set the cutting depth of a tool. It is commonly used for v-grooving ACM materials but can be used where ever high precision depths are required.

- The ELTE PF Reducer Bushing is used specifically for 5 hp ELTE spindles. It enables the use of the bellows or nose rider options for the smaller spindles.

- This is a replacement blast gate for high capacity pressure feet.
- The Blast Gate allows you to adjust the amount of air going into the pressure foot depending on the application. It is used to replace damaged blast gates.